***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Spoiler for 2010 CJ Lancer

Exterior Parts/Accessories & Modifications.

Moderators: Moderators, Senior Moderators

DamnRanga
Lancer Learner
Lancer Learner
Posts: 2
Joined: Wed May 13, 2020 3:20 pm

Spoiler for 2010 CJ Lancer

Postby DamnRanga » Fri May 15, 2020 7:28 pm

Hi Everyone,
I have recently decided that i would like to put a spoiler on my 2010 CJ Lancer.
Currently I have the Activ spoiler on but i would like to replace that with either the APR GTC-200 or the replica Evo X spoiler
I am unsure as whether these would fit directly on or whether i would have to drill new holes.
I would prefer not to have to drill new holes as I am afraid i will screw up and have a hole in my boot i dont need.
It would be much appreciated if someone has either of these spoilers and could let me know if they fit.

Thanks!

User avatar
bumblebee
Post Monster
Post Monster
Posts: 3059
Joined: Mon Jun 12, 2017 7:22 pm
Location: Australia

Re: Spoiler for 2010 CJ Lancer

Postby bumblebee » Fri May 15, 2020 8:25 pm

I have swapped out my Activ wing with a Ralliart and it's a direct fit
Even if you have to drill a hole
Use a piece of thib card board as a template on the new wing and then drill the hole
The Evo X wing from memory had a plastic clip on it that could be cut off if needed
I did that to the RA
Been on for a few years now
No drama

Have a look thru the forum
I chopped a hole in the boot lid one inch square to fit an OEM reverse camera cover
Use the same principle I did to mark the holes to drill in the boot.
Where are you located?
Someone maybe close by to help out

User avatar
lancer2014
Lancer ES/EX
Lancer ES/EX
Posts: 189
Joined: Tue May 17, 2016 12:35 pm
Location: Puerto Rico

Re: Spoiler for 2010 CJ Lancer

Postby lancer2014 » Sat May 16, 2020 12:32 pm

I have installed the evo x replica and the screws fitted into the original holes
RRM crank pulley
RA snorkel
Takeda intake
Ecu reflash
Magnaflow cat back 2.5
Tein Flex Z Coilovers
Avid 1- 06 18 x 8.5 x 35et
Hidro Real Carbon

User avatar
bumblebee
Post Monster
Post Monster
Posts: 3059
Joined: Mon Jun 12, 2017 7:22 pm
Location: Australia

Re: Spoiler for 2010 CJ Lancer

Postby bumblebee » Sat May 16, 2020 2:02 pm

The template for the RA, Evo X , Activ wing where they bolt to is all the same

YAY!

DamnRanga
Lancer Learner
Lancer Learner
Posts: 2
Joined: Wed May 13, 2020 3:20 pm

Re: Spoiler for 2010 CJ Lancer

Postby DamnRanga » Sun May 17, 2020 9:32 am

Thanks for the help everyone!
I'm still currently looking for a cheap evo x spoiler that fits the es but they all seem to cost so much.
The cheapest i could find was about $215 but they have been out of stock for a while.
The next closest place is bodykit kingdom to me and they have one for $415.
i would not like to spend that much on one but am unsure where to look.

One again thanks everyone for the help you have already given me!

User avatar
bumblebee
Post Monster
Post Monster
Posts: 3059
Joined: Mon Jun 12, 2017 7:22 pm
Location: Australia

Re: Spoiler for 2010 CJ Lancer

Postby bumblebee » Sun May 17, 2020 11:27 am

Once you buy a new wing don't be surprised if you need to paint it
Have a chat to Jimmy at evolution racing spares in Sydney, he is bound to have one off a wreck already painted and ready to roll


Return to “Exterior”

Who is online

Users browsing this forum: No registered users and 22 guests