Page 10 of 16
Posted: Fri Mar 22, 2013 1:51 am
by denzza
Good man
Yeah ill have to deliver it.. should be about 30$ bucks extra to you. If thats alright ?
Posted: Fri Mar 22, 2013 1:55 am
by JaZira5
denzza wrote:Good man
Yeah ill have to deliver it.. should be about 30$ bucks extra to you. If thats alright ?
I'm good and green to go (Yes, I'm ok with it). I've allotted funds for this. I'll just have to hold back 2 months before getting a new set of DBA rotors.. >.<
Posted: Fri Mar 22, 2013 2:25 am
by denzza
Grumpy wrote:BMR86Z for me thanks.
Recommended BMR86XZ with Lateral locks ( KLL124)
Posted: Fri Mar 22, 2013 1:39 pm
by DTGriff
Nice!, Got 10 so far.
Any idea on when this is closing?
Posted: Fri Mar 22, 2013 1:47 pm
by Fizzlefuzzle
Really wish I didn't cop that massive phone bill this month
really wanted in on this
Posted: Fri Mar 22, 2013 7:10 pm
by Meaty
Meaty VIC KLL127
If i have parts to pick up, i tend to tun up to meets
Posted: Mon Mar 25, 2013 12:02 pm
by denzza
Whats the go on this group buy? Do we have enough people?
Hopefully we get it in before the Mt Gambia meet for you DTGriff
Posted: Mon Mar 25, 2013 6:21 pm
by blinklight
Blinklight SA
BMF56Z
BMR85XZ
KSB638
KSB790
Posted: Mon Mar 25, 2013 6:21 pm
by ofey
Here's the new collation of orders:
EOI LIST GB Rd 2
ACT
1. SLIPKNUT ACT BMF56XZ + KLL127
2. timmo91 ACT BMR86XZ + KLL124
NSW:
1. Hoges NSW BMF56XZ + KLL127
NT:
1. Strez NT BMF56XZ + BMR85XZ
VIC:
1. DTGriff VIC BMR86XZ + KLL124
2. Denzza VIC BMF56XZ + KLL127
3. quachj VIC BMF56Z + BMR86XZ + KLL124
4. Grumpy VIC BMR86XZ
5. Meaty VIC KLL127
SA:
1. Tac89 SA BMR86XZ + KLL124
2. Blinklight SA BMF56Z + BMR85XZ + KSB638 + KSB790
QLD:
1. JaZira5 QLD BMF56XZ + KLL127
I'm going to say this is enough if everyone comes to the party.
You decide if I should close it now.
Though, QLD, NSW and NT are going to be paying stupid money for postage since only 1 or 2 persons in each state.
Also a word of advice:
1. Check if you have sway bar links. Some of the newer CJs came without them.
2. For those going for the thicker sway bar, do you really need that stiffness? Do you swerve around or do you take corners at 100kmh?
Take a guess, in a case where the bar doesn't flex, guess what flexes instead? Unecessary strain. The 24mm one will suffice on its highest setting (of 3 holes), that's equivalent to the 26mm one on its lowest setting.
Posted: Mon Mar 25, 2013 6:31 pm
by DTGriff
I vote to close now
Posted: Mon Mar 25, 2013 6:34 pm
by ofey
Doesn't matter if the boys in other states will be paying stupid money for postage?
Posted: Mon Mar 25, 2013 6:44 pm
by Strez
Never thought about the difference of the 26mm and 24mm ones. I'm not a racer so I'd say the 24mm should suffice. Switch mine to BMF56Z instead of the BMF56XZ for the front.
Also can you give a rough estimate on shipping up here? because if the shipping outweighs the savings on the bars then there isn't any point.
Posted: Mon Mar 25, 2013 6:54 pm
by ofey
Usually I'd say for any metro area about A$30 tops. NO MORE than that.
But it depends how Denzza is going to pack them.
Posted: Mon Mar 25, 2013 6:55 pm
by Strez
thats not bad for shipping. I'm cool with that