***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Help with underglow lighting - quick questions ASAP response

HID's, Bulb's + LED Interior and Exterior Illumination.

Moderators: Moderators, Senior Moderators

User avatar
jmunro1
Lancer Newbie
Lancer Newbie
Posts: 57
Joined: Tue Dec 20, 2011 5:22 pm
Location: dubbo, nsw

Postby jmunro1 » Fri May 31, 2013 6:04 pm

from memory i ran my 0 gauge wire through my firewall behind the master cylinder for the brakes there was a grommet there but dont hold me to that

User avatar
rokpapaziz
Lancer Legend
Lancer Legend
Posts: 1344
Joined: Sat Aug 13, 2011 12:18 am
Location: Brisbane

Postby rokpapaziz » Fri May 31, 2013 6:10 pm

I also run wires into the cabin from there ^^ but not everyone can access that one.

Right in behind the each of the strut towers there's grommets.

OR probably most suitable for you is in the front wheel arches where the front part of the side skirts end. There's a grommet there that you can push through and then in to the cabin under the plastic panels about where the boot and fuel door levers are on each side.

Hope that makes sense

User avatar
Speedie
Lancer MASTER
Lancer MASTER
Posts: 1751
Joined: Thu Mar 05, 2009 11:42 pm
Location: Brisbane, QLD, Australia

Postby Speedie » Fri May 31, 2013 6:11 pm

Look behind the internal wheel guards there is grommets into the chassis rail. Will come out into the cabin by your kick panels.
Image

[Evo X Brembos] [Evo X Intercooler] [Evo X UICP]

User avatar
Neo
Lancer VR/GT
Lancer VR/GT
Posts: 253
Joined: Mon Apr 09, 2012 7:02 pm
Location: Perth, W.A

Postby Neo » Fri May 31, 2013 6:47 pm

not sure if this is helpful at all.. but the grommet thru the firewall is hard to find, maybe this pic i took will help :)
Image

User avatar
Kyrus
Lancer Legend
Lancer Legend
Posts: 1019
Joined: Wed Apr 06, 2011 8:36 pm
Location: Sydney, Australia

Postby Kyrus » Sat Jun 01, 2013 11:36 am

for anything under glow lighting related question there can only be one answer:

Take those out and bin them, its not 2001 anymore
燒

User avatar
Kyrus
Lancer Legend
Lancer Legend
Posts: 1019
Joined: Wed Apr 06, 2011 8:36 pm
Location: Sydney, Australia

Postby Kyrus » Sat Jun 01, 2013 11:37 am

for anything under glow lighting related question there can only be one answer:

Take those out and bin them, its not 2001 anymore
燒

User avatar
Damir
Lancer Ralliart
Lancer Ralliart
Posts: 589
Joined: Tue Apr 02, 2013 6:56 am
Location: Melbourne, Australia

Postby Damir » Sat Jun 01, 2013 6:21 pm

each to their own
i bloody love underglows for their uniqueness
dont see them on cars and they look fat on cj's
My Build Thread : http://clubcj.net/viewtopic.php?t=14731
ROTM Winner OCTOBER 2015 (Nominated for favourite CJ)
-Australia's first airbagged CJ-

User avatar
Damir
Lancer Ralliart
Lancer Ralliart
Posts: 589
Joined: Tue Apr 02, 2013 6:56 am
Location: Melbourne, Australia

Postby Damir » Sun Jun 02, 2013 8:44 pm

its easy, ill take photos of mine if you need a little guide on where to mount and stuff like that
just make sure you ground really good and protect your soldering with heat shrink or electric tape
use an existing 12v from your car and that should have a fuse too :)
My Build Thread : http://clubcj.net/viewtopic.php?t=14731

ROTM Winner OCTOBER 2015 (Nominated for favourite CJ)

-Australia's first airbagged CJ-


Return to “Lighting”

Who is online

Users browsing this forum: No registered users and 43 guests