***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

Interior Front Reading Lights

Lancer Interior Modifications.

Moderators: Senior Moderators, Moderators

reverendmarty
Lancer Newbie
Lancer Newbie
Posts: 22
Joined: Tue Dec 24, 2013 12:47 pm
Location: Brisbane, Australia

Postby reverendmarty » Wed Jan 08, 2014 6:27 pm

delta_fragma wrote:The blade connector on the bottom right corner of this pic has +12v and ground. It should unclip and pull out far enough to be able to tap 2 wires to run to the front. [img:b55a588034]http://www.clubcj.net/img/images/20131124121715_IMG_2933.jpg[/img:b55a588034]


How do you get that damn blade connector out of the roof, that four way clip is the devil.

User avatar
4B11LA
Lancer Newbie
Lancer Newbie
Posts: 24
Joined: Wed Mar 06, 2013 8:42 pm
Location: sydney, Australia

Postby 4B11LA » Sun May 04, 2014 8:35 am

If you need the genuine wiring from the roof light down to the etacs ecu or fuse box passengers foot well I have that surplus to my needs also the actual light it self 2012 VR platinum
Pm me

User avatar
lantourismo
Lancer Legend
Lancer Legend
Posts: 1248
Joined: Sat Apr 13, 2013 8:32 pm
Location: Perth, Australia

Postby lantourismo » Sun May 04, 2014 8:38 am

reverendmarty wrote:[quote:d0cc60359d=delta_fragma]The blade connector on the bottom right corner of this pic has +12v and ground. It should unclip and pull out far enough to be able to tap 2 wires to run to the front. [img:b55a588034]http://www.clubcj.net/img/images/20131124121715_IMG_2933.jpg[/img:b55a588034][/quote:d0cc60359d] How do you get that damn blade connector out of the roof, that four way clip is the devil.


Easiest way is to pull the roof lining down from the front, invest In a trim removal tool, the sun visor clips are nasty things to remove with a screwdriver

User avatar
ben.sargent
Lancer Learner
Lancer Learner
Posts: 1
Joined: Fri Dec 29, 2017 2:11 pm

Re: Interior Front Reading Lights

Postby ben.sargent » Wed Jan 10, 2018 10:04 am

Hey Guys, I know this is an old thread so sorry in advance for newb questions. Just acquired a 2010 Es sedan and put map lights in last night. I have the issue where they will only come on with doors and would like to source constant 12v so I can use them anytime. Dome light has no wiring itself when removed, it slips out of/into a clip which is attached to the dome roof bracket. The dome roof clip has 2 wires coming out the back which are black and black with a white stripe. I noticed one of the screws is a ground as well. I tapped the 2 black/black+white stripe wires from the A pillar and ran wiring under roof lining to the front map light as there is no flex in the dome light loom at all nor can I get fingers in to disconnect them from the clip. I referred to previous thread images for map light wiring and I have the yellow disconnected at present which is ACC however, would like to hook up 12V constant so I can use anytime. Can anyone point me in the direction of a 12v constant located in passenger fuse box with noting colors that I can tap? It is easier to run wiring up from there than from the centre dash/console. Thanks.

User avatar
Mooman
Lancer VR/GT
Lancer VR/GT
Posts: 243
Joined: Wed Aug 12, 2015 12:29 pm
Location: Melbourne, Australia

Re: Interior Front Reading Lights

Postby Mooman » Thu Jan 11, 2018 7:05 am

Are they the proper lancer lights in the front? If so you can turn them on by pressing in the clear lens at the indent on either side.

Image

User avatar
aspir3
Site Admin
Site Admin
Posts: 8147
Joined: Tue Oct 27, 2009 6:15 pm
Location: adelaide

Re: Interior Front Reading Lights

Postby aspir3 » Thu Jan 11, 2018 5:21 pm

They should have powers to them all the time. They are controlled by the earth.
Did you fit an earth to it?
Image
Nice work Skip' now where the bloody hell is Sunny?

Please check out my GARAGE and feel free to leave a comment.


Return to “Interior”

Who is online

Users browsing this forum: No registered users and 3 guests